• <td id="ae0io"></td>
  • <button id="ae0io"><samp id="ae0io"></samp></button>
  • <kbd id="ae0io"><tt id="ae0io"></tt></kbd>
  • Product Center 產品中心

    產品中心

    當前位置: 首頁 > 產品中心
     BE06 無溶劑型自流平環氧地坪漆
    來源: 點擊數:775次 更新時間:2019-6-4 8:55:39
    產品名稱:OMELON BE06
    產品介紹:
    GENERAL
    BE06, is an excellent 100% epoxy flooring self-levelling, with impact resistance and chemical resistance, for application on concrete surfaces.BE06, is ecologically and designed for filling losses of Concrete. EURO-level 2 BE06, MUST BE applied overES302 clear (wet surfaces), or EURO-steel BE23 (dry surfaces).
    總述
    BE06 是一種優異的100%環氧的自流平的涂料,具有抗沖擊性,抗化學性,用于混凝土表面的涂裝. BE06 從生態上設計,用來填充混凝土的缺損部分. BE06 它必須涂裝在EURO-floor ES302 (濕表面),或BE23(干表面)涂層的上面.
    FEATRURES

    NO HARMFUL SOLVENT VAPOURS.

    NO VOC’s

    Superior impact resistance.

    NON-FLAMMABLE.

    Good chemical, solvent and water immersion resistance.

    No more problems with DEW POINT.

    Applications up to 1.18” tick on horizontal surfaces.

    Cost savings on surface preparation.

    Excellent protective properties.

    產品特性

    無有害揮發物

    無揮發性有機化合物

    高抗沖擊性能

    不可燃

    具耐化學品,耐溶劑,耐水浸泡的優良性能

    無露點限制

    在水平面上可涂裝高達1.18英寸的厚度

    節省表面處理的成本

    優異的保護性

    RECOMMENDED USES

    REPAIR OF CONCRETE BOTTOM TANKS

    Potable water tanks.

    Selected chemical tanks.

    INDUSTRIAL FLOORS.

    Glass factories.

    Food factories.

    Car factories.

    Schools.

    Workshops.

    推薦用途
    修復混凝土底罐

    飲用水罐

    部分化學品罐

    工業地坪

    玻璃廠

    食品廠

    汽車廠

    學校

    車間

    SPECIFICATION DATA
    技 術 參 數
    Binder Type/Pigment Type
    Modified epoxy/Amine composite- Chemical resistant pigments&extenders.
    基料類型/顏料類型
    改性環氧/復合胺,耐化學顏填料
    Colors
    BE0600(white), BE0699(black), BE0610(grey), or custom request.
    顏色
    BE0600(白色),BE0699(黑色),BE0610(灰色)或用戶要求
    Finish
    Gloss
    表面
    高光
    Mixing ratio
    5(base) to 1(curing agent) by weight, 3.1(base) to 1(curing agent) by volume.
    混合比率
    重量比5(基料):1(固化劑),體積比3.3(基料):1(固化劑)。
    Curing agent
    CA14
    固化劑
    CA14
    Specific gravity
    1.41±0.03Kg/ Lt
    比重
    1.41±0.03公斤/升
    Solid by Volume
    100%(theoretical)
    體積固體份
    100%(理論值)
    Pot Life
    30 minutes at 23℃(73.4℉)
    混合使用期
    30分鐘,23℃(73.4℉)
    Flash point(Abel)
    Base: >100℃(>212℉);Curing agent: >100℃(>212℉)
    閃點
    基料:>100℃; 固化劑:>100℃
    Theoretical covering capability
    0.28Sq.m/kg.(1.38 q.ft/Lb) at 25 microns (100 mils)
    理論覆蓋能力
    0.28平方米公斤,2500um厚
    Typical film thickness per coat
    Wet:2500 microns(100 mils); Dry:2500 mircons (100mils)
    每層膜厚
    濕膜:2500um,干膜:2500um
    Thinner
    Material: none -Cleaning: EURO-thinner TH03
    稀釋劑
    材料:無; 清洗劑:TH03
    VOC
    Does not contain. It is a 100% solids epoxy product.
    揮發性有機化合物
    不含,為100%的固體環氧產品。
    Drying time
    Surface dry: approx. 3 hours (at 23℃ (73.4℉) and 50% relative hunidity)
    干燥時間
    表干:3小時,在23°C和50%相對濕度下。
    Overcoating time
    Min:16 hours at 23℃ ;Max: 7 days at 23℃ (73.4℉)
    重涂時間
    最短:16小時,在23°C下。最長:7天在23°C下。
    Recommended primers
    EURO-floor ES302 clear (wet), EURO-steel BE23 (dry)
    推薦底漆
    ES302 潮濕表面, BE23干燥表面
    Ambient temperature
    Min: >5℃(41℉)-Max: Not applicable. Substrate is the important factor when applying below 5℃(41℉), a different cure is required.
    環境溫度
    最低:>5°C,最高:無,,基底是重要因素,當于5°C以下涂覆時要求不同的固化方法。
    Substrate temperature
    Min:0℃(32℉)- Max:50℃(122℉)
    底材溫度
    最低:0°C,最高:50°C
    Storage and Shelf life
    The product should be kept in a cool well ventilated places protected from high temperatures. Container MUST BE kept tightly closed. Shelf life:1 year
    儲存及有效期
    產品應保存于陰涼、通風良好的地方,避免過高的溫度。容器必須牢固密封。有效期:1年 。
    APPLICATION GUIDE
    施 工 指 導
    SURFACE PREPARATION
    BE06, is designed for application on horizontal concrete surfaces over a suitable primer. EURO-level 2 BE06, must be applied on surfaces without dust, oil, Grease and other contaminations.
    表面處理
    BE06,用于涂有適當底漆的水平混凝土表面。BE06,必須涂覆在沒有塵土、油脂和其它污染物的表面上。
    APPLICATION
    BE06, can be applied, by trowel, spreader, squeegee or roller. Care should be taken that proper and uniform film thickness is obtained. BE06, can be applied up to 3 cm (1,18”), tick on Horizontal surfaces. A minimum of two days cure should be allowed Before floor is put into service. Product may be applied on wet or Dry surfaces in 100% humidity conditions. Ventilation It is very important for the safety of the applicator and the proper performance of EURO-level 2 BE06, that good ventilation be provided to all portions of the enclosed area. Dry air IS NOT a must since EURO-level 2 BE06. DOES NOT contain solvents, can be applied under severe conditions of humidity.
    施工
    BE06,可采用刮涂、輥涂。注意得到正確的且均勻的膜厚。
    BE06,可以在水平面上涂裝厚度高達3公分。地坪在使用之前應該有至少兩天的固化時間,產品可以在濕的或干的表面上,在濕度為100%的條件下涂裝。
    通風
    作業區的各個部位保持良好的通風對操作人員的安全和施工效果都是非常重要的。 空氣不一定要干燥,由于本產品不含溶劑,可以在嚴酷的濕度條件下涂覆施工。
    SAFETY
    WARNING: Avoid breathing vapors. Do not get in eyes on skin or clothing, Use ear ,eye and skin protective equipment. Use appropriate respirator. Wash skin thoroughly after use and water. Launder clothing before reuse. If not breathing gives artificial respiration, preferably mouth-to-mouth, and call physician.
    BURNS: Exothermic reaction causes product to heat which is normal.
    Be careful handling after mixing product. Use gloves.
    FIRST AID: In case of eye contact immediately flush with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash skin contact area with soap.
    安全措施
    警告:避免吸入汽霧。請勿觸及眼睛皮膚。要使用眼、耳、皮膚的防護用具,使用合適的面具。使用后用清水徹底的清洗皮膚。衣物再次使用前要洗滌。如果沒有呼吸要進行人工呼吸,最好嘴對嘴,并請醫生處理。
    灼傷:放熱反應會使產品變熱,超出正常水平。在混合后要小心處理。使用手套。
    急救:如果不慎接觸了眼睛,立即用清水沖洗至少15分鐘,并脫去污染的衣鞋,用肥皂清洗接觸后的皮膚。
    DISCLAMER
    This is not a specification and all information is given in good faith. Every values presented as Theoretical were calculated from the product formula If requested, Euronavy can inform any internal measurement method used to determinate any given value presented. Since conditions of use are beyond the manufacturers control information contained herein is without warranty, implied or otherwise, and final determination of the suitability of any information or material for the use contemplated is the sole responsibility of user. The product is intended for professional use only. In case of any doubt, contact your local agent.
    提請注意
    此文件不是正式的技術文件,所列出的信息是可靠的。提供的每個數值都是作為理論數據從產品的配方中計算出來的。如果需要,Euronavy可以告知任何上述給出數據的內部常用測量確定方法。由于使用條件非生產商所能控制,這里的信息不作為擔保。產品僅限于專業人員使用。如有任何問題,請與當地相關機構聯系。
    【刷新頁面】【加入收藏】【打印此文】 【關閉窗口】
    上一篇:BE07 無溶劑型環氧彈性涂料 下一篇:HE25 乙烯基酯玻璃鱗片涂料